RACK board ZMC-2 - Placă de montaj cu șină EURO TH35 și două porturi Keystone

Cod: R77220
148,27 Lei
Preţ cu TVA Rabat Cant. Validitate
148,27 Lei 0 % de la 1 buc.


Garanţie 5 ani.

Suport tehnic


RACK board allows installers to make use both of the front and side surfaces of 19" RACK cabinets, which are accessible after dismantling the side walls. The solution enables unprecedented volume filling factor of the cabinets, while maintaining good access to all signal distribution devices, with proper ventilation, connection transparency, application of patch panels to connect all inbound and outbound cables. All the features make it easy for technicians to diagnose the network during operation.
Detailed information on the RACK board vertical mounting system is available here.
To mount the ZMB panels, it is necessary to use the ZMC front panels. The width of the ZMC panel is specially designed to enable the application of the ZMB panels on the side surfaces of the rack cabinet.
The ZMC-2 R77220 component is used in a situation where, next to a few devices (length of the TH35 rail is 190 mm) mounted on the EURO rail, other devices should be mounted vertically. The component has a width of 180 mm and a height of 170 mm. It is made of hard PA11 aluminum sheet with a thickness of 1.5 mm. Thanks to this, it has sufficient stiffness and at the same time the material allows for easy drilling of the necessary assembly holes. The vertical panel of the ZMC-2 assembly has two holes for keystone modules. ZMC-2 can be loaded with evenly distributed devices with a total weight of 12 kg. The kit includes four caged nuts for mounting the component in the cabinet.
Example application of the ZMC-2 component of the RACK board system: SRM-522 R80522 single-cable multiswitch with dSCR/Unicable support, TERRA tdx480 R81621 8xDVB-S/S2 (8PSK, QPSK) - 8xDVB-T (COFDM) transmodulator, and UP413 R82533 power supply

Example application of the ZMC-2 component of the RACK board system: Optical Receiver TERRA OR501MW (QUAD + DVB-T/DAB/FM), Optical Receiver TERRA OR501W (QUATRO + DVB-T/DAB/FM), Channel Amplifier at440 R82522, Broadband Amplifier ma400 R82520, and Power Supply UP413 R82533.
For example, the ZMC-2 component can be used for mounting TERRA at440 R82511, TERRA ma400 R82520 and DR-60-12 R82532 devices on the EURO TH35 rail, and two optical receivers TERRA OR501W QUATRO A9877 on the vertical panel, which are connected via optical patch cords with keystone sockets.
Main features of the RACK board vertical mounting system:
  • Predefined installation sets for individual equipment configurations enable simple and quick assembly.
  • RACK board mounting panels allow for installing the equipment items and cables so that the components are placed in a clear and aesthetic way. The highly professional solution ensures that the longer cables are hidden in the middle part of the cabinet, whereas the connections and the devices are easily available (in opposite to placing such devices horizontally). This improves the equipment cooling and facilitates measurement and adjustment procedures.
  • The RACK board system is a universal solution - originally dedicated for Terra equipment, it can be easily adopted for use in GSM (repeaters), network (routers and switches) and other applications.
  • Because every device in the RACK board system is placed vertically and it does not adhere to any other device or element of the RACK cabinet, it is naturally cooled by the air circulation inside the cabinet.
  • Each device has its own mounting panel and the spaces between devices allow for easy wiring.
  • Hardware components of RACK board system:
    • ZMB series - side assembly components for installing on the side surfaces of large standing cabinets. Currently, we offer panels for mounting in 800 x 600 cabinets.
    • ZMC series - front assembly components that can be installed together with ZMB panels.
    • ZMD series - front assembly components for hanging or standing cabinets (cannot be used with ZMB series due to 19'' width).
  • With the RACK board system the installer can make use not only of the front of a RACK cabinet (rails with 19" spacing) but also of the side spaces - the access to those devices is obtained by dismantling side walls of the RACK. The ZMB side assembly is mounted (on the left and/or right side) to the front and rear RACK rail. Currently we offer the ZMB-1-800 assembly for 600x800 mm standing RACK cabinets.
  • The installer can use ZMC front-mount assemblies in several versions. They allow for installing in the front part of the cabinet both the 19’’ standard devices but also other equipment mounted on the EURO TH35 rail or on vertical planes.
  • The elements of the RACK board system are made of hard aluminum sheets PA11 (DIN, ISO: AlMg3), powder painted in RAL9004 color. If the prepared mounting holes do not fit the mounted equipment, it is easy to drill new ones.
  • The ZMD components can be used in standing or hanging cabinets, but they cannot be used together with ZMB components that take the whole 19" width.
  • The cables providing signals from antennas are connected to the patch panel with F connectors which, via bridges, transmits the signals to a next patch panel and the required devices. By taking the connection bridges, the installer/technician can measure the input signal in any path.
  • All outbound cables are also connected to panels with F connectors. Each connector can be marked with the number of the corresponding apartment, which helps to perform diagnostics of the whole distribution network, beginning with the measurements of the output signals.


tip Ramă rack